Zum Inhalt springen
ATS Mini Controller
Offline
Radio + appTuning2 Min. Lesezeit

Bands & the band plan

How the ATS Mini organises its coverage into named bands (FM, the shortwave meter bands, mediumwave, the ham bands and CB) and how to jump between them.

The ATS Mini doesn’t tune as one long dial. It organises its coverage into named bands, each with its own frequency range, a default mode, and a memory of where you last were. This guide explains the bands and how to move between them.

What the radio covers

Two worlds, really. There is VHF FM broadcast from 64 to 108 MHz. And there is everything from 150 kHz to 30 MHz, which covers longwave, mediumwave and the whole shortwave range, in AM and single sideband. How much of that you actually hear depends mostly on what you plug into the antenna jack; see the antenna guide.

The named bands

  • VHF. The FM broadcast band (64 to 108 MHz). FM is only available here.
  • ALL. A catch-all from 150 to 30000 kHz for tuning freely across longwave, mediumwave and shortwave without band limits.
  • Shortwave broadcast bands. The classic "meter bands" (90M, 75M, 60M, 49M, 41M, 31M, 25M, 22M, 19M, 16M, 15M, 13M, 11M), preset to AM, where the international broadcasters live.
  • Mediumwave (MW1, MW2, MW3). The AM broadcast band and its edges.
  • Amateur (ham) bands. 160M, 80M, 40M and 30M default to LSB; 20M, 17M, 15M, 12M and 10M default to USB.
  • CB. The Citizens’ Band around 27 MHz, in AM.

Switching bands

Use the previous and next band buttons, or pick a band from the list. The app takes the shortest way around the band list to get there, and each band remembers the frequency and mode you last used in it. Hop over to FM and back, and you land right where you left off.

Default mode is just a starting point

Each band opens in a sensible default mode: FM on VHF, AM on the broadcast bands, LSB or USB on the ham bands. You can change mode freely afterwards, except on VHF, which is FM-only. See Reception modes.

Empfohlenes Zubehör

  • XHDATA AN-80 reel antennaAntennaA reel of wire hung out of a window is the cheapest way to hear the shortwave bands listed here.
  • Telescopic whip antennaAntennaFM and the VHF airband work straight off the whip — length is the only upgrade they ask for.
  • SMA-M to coaxial adapterAdapter / connectorAnything bigger than a whip meets the radio at its SMA jack, so settle the adapter before buying the antenna.

Am eigenen Radio ausprobieren

Über USB oder Bluetooth verbinden und im Controller mitverfolgen.

Controller öffnen

Mehr

Gerät

Entdecken

Einstellungen

Design

Willkommen bei ATS Mini Controller

Diese Web-App verbindet sich per USB oder Bluetooth LE mit deinem ATS Mini Radio, sodass du es direkt vom Computer oder Smartphone aus steuern kannst. Sie ergänzt die eingebaute Firmware des Geräts um Fernabstimmung, Speicherplatzverwaltung, Screenshot-Aufnahme, Audio-Streaming, Spektrum-Scan, Theme-Bearbeitung und weitere Funktionen.

Firmware 2.34+: Verbindungsart wählen

Ab Firmware 2.34 lässt sich das Radio per USB oder Bluetooth LE fernsteuern. Wähle nach dem, was dir wichtiger ist: schnelle Screenshots (USB) oder sauberer Ton am 3,5-mm-Ausgang des Radios (Bluetooth) – die beiden Übertragungswege haben gegensätzliche Stärken.

  • USB Serial

    Settings USB Port von Off auf Ad hoc ändern

    Funktioniert in jedem Chromium-basierten Browser. Erfordert ein USB-C-Kabel mit Datenleitungen (öffnet in einem neuen Tab).

    Am besten für Screenshots und Theme-Bearbeitung. Übertragungen sind in ein bis zwei Sekunden fertig. Die Audioaufnahme ist bei angeschlossenem Kabel verrauscht – dem Radio fehlt die Filterung, um seinen 3,5-mm-Ausgang von der USB-Versorgungsleitung zu isolieren, sodass Brummen und Schaltstörungen in den Audiopfad gelangen.

  • Bluetooth LE

    Settings Bluetooth Modus auf Ad hoc stellen

    Chrome / Edge / Opera auf dem Desktop oder unter Android. BLE ist in Firmware 2.34 experimentell.

    Am besten für sauberen Ton. Bluetooth LE überträgt nur die Fernsteuerung, nie Ton: Der läuft weiterhin per Kabel vom 3,5-mm-Ausgang des Radios zum Computer. Ohne USB-Kabel läuft das Radio auf Akku, sodass dieser Ausgang frei von den USB-Versorgungsstörungen bleibt, die bei einer Kabelverbindung durchschlagen. Screenshots sind wegen der begrenzten BLE-Übertragungsrate der Firmware deutlich langsamer (~30 s).

Mehr als eine Firmware

Neben der offiziellen Firmware enthält die App Profile für den Monster-Fork und für die Firmware von H. J. Berndt. Welche davon läuft, erkennt sie an den Antworten des Radios, du musst also nichts auswählen. Passt keine, sagt sie das offen, statt zu raten.

  • Berndt-Firmware wird nie unterstellt. Sie nutzt einige Tasten der offiziellen Firmware mit, und was diese dort bewirken, ist nicht geklärt – deshalb fragt die App, bevor sie darauf umschaltet.
  • Fehlende Bedienelemente sind Absicht. Was eine Firmware nicht kann, steht gar nicht auf der Seite, statt ausgegraut zu sein, und auf Berndt-Firmware gehen Befehle einzeln hinaus, mit einigen Sekunden Abstand.
Wie die App mit anderer Firmware umgeht (öffnet in einem neuen Tab)

Tastenkürzel

Einzelne Tasten steuern das Radio auf der Controller-Seite, außer während du in ein Feld tippst.

←→
Einen Schritt abstimmen
↑↓
Lautstärke auf / ab
Enter
OK
BN
Nächstes / vorheriges Band
MV
Nächste / vorherige Betriebsart
SA
Nächster / vorheriger Schritt
WQ
Nächste / vorherige Bandbreite
GF
AGC auf / ab
LK
Hintergrundlicht heller / dunkler
IU
Kalibrierung auf / ab
OP
Ruhemodus ein / aus
T
Statusprotokoll umschalten
C
Screenshot
H
Empfang protokollieren
D
Cockpit-Ansicht
⌘K
Seiten & Sender suchen